From: Andy Gospodarek <gospo@redhat.com>
Date: Fri, 14 Nov 2008 11:14:29 -0500
Subject: [net] ixgbe: add support for 82598AT
Message-id: 20081114161429.GE20392@gospo.rdu.redhat.com
O-Subject: [RHEL5.3 PATCH] ixgbe: add support for 82598AT
Bugzilla: 454910
RH-Acked-by: John W. Linville <linville@redhat.com>
RH-Acked-by: Neil Horman <nhorman@redhat.com>
RH-Acked-by: Prarit Bhargava <prarit@redhat.com>
This patch adds support for the new 82595AT adapters. Though we
previously removed support for this adapter by dropping the pci-id, this
adds it back and includes the support needed to make it work properly.
This is mostly a backport of the following upstream commit with a small
recursion fix during initialization as well:
commit 0befdb3e0a26a8949063915274e1bec8873c526b
Author: Jesse Brandeburg <jesse.brandeburg@intel.com>
Date: Fri Oct 31 00:46:40 2008 -0700
ixgbe: add device support for 82598AT (copper 10GbE) adapters
Intel is currently shipping support for adapters with a phy
that does 10GBase-T (copper), which is 10 Gigabit ethernet
over standard Category 6 cabling.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This should completely satisfy the request in RHBZ 454910.
diff --git a/drivers/net/ixgbe/ixgbe.h b/drivers/net/ixgbe/ixgbe.h
index ff7615d..7ff9bb3 100644
--- a/drivers/net/ixgbe/ixgbe.h
+++ b/drivers/net/ixgbe/ixgbe.h
@@ -260,6 +260,7 @@ struct ixgbe_adapter {
#define IXGBE_FLAG_RX_PS_ENABLED (u32)(1 << 3)
#define IXGBE_FLAG_IN_NETPOLL (u32)(1 << 4)
#define IXGBE_FLAG_IMIR_ENABLED (u32)(1 << 5)
+#define IXGBE_FLAG_FAN_FAIL_CAPABLE (u32)(1 << 20)
#define IXGBE_FLAG_RSS_ENABLED (u32)(1 << 6)
#define IXGBE_FLAG_VMDQ_ENABLED (u32)(1 << 7)
diff --git a/drivers/net/ixgbe/ixgbe_82598.c b/drivers/net/ixgbe/ixgbe_82598.c
index f96358b..34869bf 100644
--- a/drivers/net/ixgbe/ixgbe_82598.c
+++ b/drivers/net/ixgbe/ixgbe_82598.c
@@ -193,7 +193,7 @@ static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw)
case IXGBE_DEV_ID_82598_CX4_DUAL_PORT:
media_type = ixgbe_media_type_fiber;
break;
- case IXGBE_DEV_ID_82598AT_DUAL_PORT:
+ case IXGBE_DEV_ID_82598AT:
media_type = ixgbe_media_type_copper;
break;
default:
@@ -365,7 +365,7 @@ static s32 ixgbe_setup_copper_link_82598(struct ixgbe_hw *hw)
hw->mac.link_mode_select = IXGBE_AUTOC_LMS_KX4_AN;
/* Set up MAC */
- hw->mac.ops.setup_link(hw);
+ ixgbe_setup_mac_link_82598(hw);
return status;
}
diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c
index 69c45c3..35688bd 100644
--- a/drivers/net/ixgbe/ixgbe_ethtool.c
+++ b/drivers/net/ixgbe/ixgbe_ethtool.c
@@ -147,6 +147,8 @@ static int ixgbe_set_settings(struct net_device *netdev,
{
struct ixgbe_adapter *adapter = netdev_priv(netdev);
struct ixgbe_hw *hw = &adapter->hw;
+ u32 advertised, old;
+ s32 err;
switch (hw->phy.media_type) {
case ixgbe_media_type_fiber:
@@ -155,6 +157,31 @@ static int ixgbe_set_settings(struct net_device *netdev,
return -EINVAL;
/* in this case we currently only support 10Gb/FULL */
break;
+ case ixgbe_media_type_copper:
+ /* 10000/copper and 1000/copper must autoneg
+ * this function does not support any duplex forcing, but can
+ * limit the advertising of the adapter to only 10000 or 1000 */
+ if (ecmd->autoneg == AUTONEG_DISABLE)
+ return -EINVAL;
+
+ old = hw->phy.autoneg_advertised;
+ advertised = 0;
+ if (ecmd->advertising & ADVERTISED_10000baseT_Full)
+ advertised |= IXGBE_LINK_SPEED_10GB_FULL;
+
+ if (ecmd->advertising & ADVERTISED_1000baseT_Full)
+ advertised |= IXGBE_LINK_SPEED_1GB_FULL;
+
+ if (old == advertised)
+ break;
+ /* this sets the link speed and restarts auto-neg */
+ err = hw->mac.ops.setup_link_speed(hw, advertised, true, true);
+ if (err) {
+ DPRINTK(PROBE, INFO,
+ "setup link failed with code %d\n", err);
+ hw->mac.ops.setup_link_speed(hw, old, true, true);
+ }
+ break;
default:
break;
}
diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c
index 02762fd..30939da 100644
--- a/drivers/net/ixgbe/ixgbe_main.c
+++ b/drivers/net/ixgbe/ixgbe_main.c
@@ -71,6 +71,8 @@ static struct pci_device_id ixgbe_pci_tbl[] = {
board_82598 },
{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82598AF_SINGLE_PORT),
board_82598 },
+ {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82598AT),
+ board_82598 },
{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82598EB_CX4),
board_82598 },
{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82598_CX4_DUAL_PORT),
@@ -768,6 +770,18 @@ static void ixgbe_set_itr_msix(struct ixgbe_q_vector *q_vector)
return;
}
+static void ixgbe_check_fan_failure(struct ixgbe_adapter *adapter, u32 eicr)
+{
+ struct ixgbe_hw *hw = &adapter->hw;
+
+ if ((adapter->flags & IXGBE_FLAG_FAN_FAIL_CAPABLE) &&
+ (eicr & IXGBE_EICR_GPI_SDP1)) {
+ DPRINTK(PROBE, CRIT, "Fan has stopped, replace the adapter\n");
+ /* write to clear the interrupt */
+ IXGBE_WRITE_REG(hw, IXGBE_EICR, IXGBE_EICR_GPI_SDP1);
+ }
+}
+
static irqreturn_t ixgbe_msix_lsc(int irq, void *data, struct pt_regs *regs)
{
struct net_device *netdev = data;
@@ -781,6 +795,8 @@ static irqreturn_t ixgbe_msix_lsc(int irq, void *data, struct pt_regs *regs)
mod_timer(&adapter->watchdog_timer, jiffies);
}
+ ixgbe_check_fan_failure(adapter, eicr);
+
if (!test_bit(__IXGBE_DOWN, &adapter->state))
IXGBE_WRITE_REG(hw, IXGBE_EIMS, IXGBE_EIMS_OTHER);
@@ -1110,6 +1126,8 @@ static irqreturn_t ixgbe_intr(int irq, void *data, struct pt_regs *regs)
}
+ ixgbe_check_fan_failure(adapter, eicr);
+
if (netif_rx_schedule_prep(adapter->q_vector[0].dummy_netdev)) {
adapter->tx_ring[0].total_packets = 0;
adapter->tx_ring[0].total_bytes = 0;
@@ -1212,6 +1230,8 @@ static inline void ixgbe_irq_enable(struct ixgbe_adapter *adapter)
{
u32 mask;
mask = IXGBE_EIMS_ENABLE_MASK;
+ if (adapter->flags & IXGBE_FLAG_FAN_FAIL_CAPABLE)
+ mask |= IXGBE_EIMS_GPI_SDP1;
IXGBE_WRITE_REG(&adapter->hw, IXGBE_EIMS, mask);
IXGBE_WRITE_FLUSH(&adapter->hw);
}
@@ -1619,6 +1639,13 @@ static int ixgbe_up_complete(struct ixgbe_adapter *adapter)
IXGBE_WRITE_REG(hw, IXGBE_EIAM, IXGBE_EICS_RTX_QUEUE);
}
+ /* Enable fan failure interrupt if media type is copper */
+ if (adapter->flags & IXGBE_FLAG_FAN_FAIL_CAPABLE) {
+ gpie = IXGBE_READ_REG(hw, IXGBE_GPIE);
+ gpie |= IXGBE_SDP1_GPIEN;
+ IXGBE_WRITE_REG(hw, IXGBE_GPIE, gpie);
+ }
+
mhadd = IXGBE_READ_REG(hw, IXGBE_MHADD);
if (max_frame != (mhadd >> IXGBE_MHADD_MFS_SHIFT)) {
mhadd &= ~IXGBE_MHADD_MFS_MASK;
@@ -2299,6 +2326,9 @@ static int __devinit ixgbe_sw_init(struct ixgbe_adapter *adapter)
rss = min(IXGBE_MAX_RSS_INDICES, (int)num_online_cpus());
adapter->ring_feature[RING_F_RSS].indices = rss;
adapter->flags |= IXGBE_FLAG_RSS_ENABLED;
+ if (hw->mac.ops.get_media_type &&
+ (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_copper))
+ adapter->flags |= IXGBE_FLAG_FAN_FAIL_CAPABLE;
/* Enable Dynamic interrupt throttling by default */
adapter->rx_eitr = 1;
@@ -3238,6 +3268,26 @@ static void ixgbe_netpoll(struct net_device *netdev)
#endif
/**
+ * ixgbe_link_config - set up initial link with default speed and duplex
+ * @hw: pointer to private hardware struct
+ *
+ * Returns 0 on success, negative on failure
+ */
+static int ixgbe_link_config(struct ixgbe_hw *hw)
+{
+ u32 autoneg = IXGBE_LINK_SPEED_10GB_FULL;
+
+ /* must always autoneg for both 1G and 10G link */
+ hw->mac.autoneg = true;
+
+ if ((hw->mac.type == ixgbe_mac_82598EB) &&
+ (hw->phy.media_type == ixgbe_media_type_copper))
+ autoneg = IXGBE_LINK_SPEED_82598_AUTONEG;
+
+ return hw->mac.ops.setup_link_speed(hw, autoneg, true, true);
+}
+
+/**
* ixgbe_napi_add_all - prep napi structs for use
* @adapter: private struct
* helper function to napi_add each possible q_vector->napi
@@ -3494,6 +3544,13 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
/* reset the hardware with the new settings */
ixgbe_start_hw(hw);
+ /* link_config depends on start_hw being called at least once */
+ err = ixgbe_link_config(hw);
+ if (err) {
+ dev_err(&pdev->dev, "setup_link_speed FAILED %d\n", err);
+ goto err_register;
+ }
+
netif_carrier_off(netdev);
netif_stop_queue(netdev);
diff --git a/drivers/net/ixgbe/ixgbe_phy.c b/drivers/net/ixgbe/ixgbe_phy.c
index 8002931..e1e82f4 100644
--- a/drivers/net/ixgbe/ixgbe_phy.c
+++ b/drivers/net/ixgbe/ixgbe_phy.c
@@ -492,3 +492,21 @@ s32 ixgbe_setup_tnx_phy_link_speed(struct ixgbe_hw *hw, u32 speed,
return 0;
}
+
+/**
+ * ixgbe_get_phy_firmware_version_tnx - Gets the PHY Firmware Version
+ * @hw: pointer to hardware structure
+ * @firmware_version: pointer to the PHY Firmware Version
+ **/
+s32 ixgbe_get_phy_firmware_version_tnx(struct ixgbe_hw *hw,
+ u16 *firmware_version)
+{
+ s32 status = 0;
+
+ status = ixgbe_read_phy_reg(hw, TNX_FW_REV,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ firmware_version);
+
+ return status;
+}
+
diff --git a/drivers/net/ixgbe/ixgbe_phy.h b/drivers/net/ixgbe/ixgbe_phy.h
index aa3ea72..6d9cd07 100644
--- a/drivers/net/ixgbe/ixgbe_phy.h
+++ b/drivers/net/ixgbe/ixgbe_phy.h
@@ -46,4 +46,8 @@ s32 ixgbe_check_tnx_phy_link(struct ixgbe_hw *hw, u32 *speed, bool *link_up);
s32 ixgbe_setup_tnx_phy_link_speed(struct ixgbe_hw *hw, u32 speed, bool autoneg,
bool autoneg_wait_to_complete);
+/* PHY specific */
+s32 ixgbe_get_phy_firmware_version_tnx(struct ixgbe_hw *hw,
+ u16 *firmware_version);
+
#endif /* _IXGBE_PHY_H_ */
diff --git a/drivers/net/ixgbe/ixgbe_type.h b/drivers/net/ixgbe/ixgbe_type.h
index 0a32b17..05a3698 100644
--- a/drivers/net/ixgbe/ixgbe_type.h
+++ b/drivers/net/ixgbe/ixgbe_type.h
@@ -38,7 +38,7 @@
/* Device IDs */
#define IXGBE_DEV_ID_82598AF_DUAL_PORT 0x10C6
#define IXGBE_DEV_ID_82598AF_SINGLE_PORT 0x10C7
-#define IXGBE_DEV_ID_82598AT_DUAL_PORT 0x10C8
+#define IXGBE_DEV_ID_82598AT 0x10C8
#define IXGBE_DEV_ID_82598EB_CX4 0x10DD
#define IXGBE_DEV_ID_82598_CX4_DUAL_PORT 0x10EC
@@ -466,14 +466,17 @@
/* PHY IDs*/
#define TN1010_PHY_ID 0x00A19410
+#define TNX_FW_REV 0xB
#define QT2022_PHY_ID 0x0043A400
/* General purpose Interrupt Enable */
-#define IXGBE_GPIE_MSIX_MODE 0x00000010 /* MSI-X mode */
-#define IXGBE_GPIE_OCD 0x00000020 /* Other Clear Disable */
-#define IXGBE_GPIE_EIMEN 0x00000040 /* Immediate Interrupt Enable */
-#define IXGBE_GPIE_EIAME 0x40000000
-#define IXGBE_GPIE_PBA_SUPPORT 0x80000000
+#define IXGBE_SDP0_GPIEN 0x00000001 /* SDP0 */
+#define IXGBE_SDP1_GPIEN 0x00000002 /* SDP1 */
+#define IXGBE_GPIE_MSIX_MODE 0x00000010 /* MSI-X mode */
+#define IXGBE_GPIE_OCD 0x00000020 /* Other Clear Disable */
+#define IXGBE_GPIE_EIMEN 0x00000040 /* Immediate Interrupt Enable */
+#define IXGBE_GPIE_EIAME 0x40000000
+#define IXGBE_GPIE_PBA_SUPPORT 0x80000000
/* Transmit Flow Control status */
#define IXGBE_TFCS_TXOFF 0x00000001
@@ -547,18 +550,23 @@
/* Extended Interrupt Cause Read */
#define IXGBE_EICR_RTX_QUEUE 0x0000FFFF /* RTx Queue Interrupt */
#define IXGBE_EICR_LSC 0x00100000 /* Link Status Change */
-#define IXGBE_EICR_MNG 0x00400000 /* Managability Event Interrupt */
+#define IXGBE_EICR_MNG 0x00400000 /* Manageability Event Interrupt */
+#define IXGBE_EICR_GPI_SDP0 0x01000000 /* Gen Purpose Interrupt on SDP0 */
+#define IXGBE_EICR_GPI_SDP1 0x02000000 /* Gen Purpose Interrupt on SDP1 */
#define IXGBE_EICR_PBUR 0x10000000 /* Packet Buffer Handler Error */
#define IXGBE_EICR_DHER 0x20000000 /* Descriptor Handler Error */
#define IXGBE_EICR_TCP_TIMER 0x40000000 /* TCP Timer */
#define IXGBE_EICR_OTHER 0x80000000 /* Interrupt Cause Active */
+
/* Extended Interrupt Cause Set */
#define IXGBE_EICS_RTX_QUEUE IXGBE_EICR_RTX_QUEUE /* RTx Queue Interrupt */
#define IXGBE_EICS_LSC IXGBE_EICR_LSC /* Link Status Change */
#define IXGBE_EICR_GPI_SDP0 0x01000000 /* Gen Purpose Interrupt on SDP0 */
#define IXGBE_EICS_MNG IXGBE_EICR_MNG /* MNG Event Interrupt */
-#define IXGBE_EICS_PBUR IXGBE_EICR_PBUR /* Pkt Buf Handler Error */
+#define IXGBE_EIMS_GPI_SDP0 IXGBE_EICR_GPI_SDP0 /* SDP0 Gen Purpose Int */
+#define IXGBE_EIMS_GPI_SDP1 IXGBE_EICR_GPI_SDP1 /* SDP1 Gen Purpose Int */
+#define IXGBE_EIMS_PBUR IXGBE_EICR_PBUR /* Pkt Buf Handler Err */
#define IXGBE_EICS_DHER IXGBE_EICR_DHER /* Desc Handler Error */
#define IXGBE_EICS_TCP_TIMER IXGBE_EICR_TCP_TIMER /* TCP Timer */
#define IXGBE_EICS_OTHER IXGBE_EICR_OTHER /* INT Cause Active */
@@ -1126,7 +1134,8 @@ struct ixgbe_adv_tx_context_desc {
#define IXGBE_LINK_SPEED_100_FULL 0x0008
#define IXGBE_LINK_SPEED_1GB_FULL 0x0020
#define IXGBE_LINK_SPEED_10GB_FULL 0x0080
-
+#define IXGBE_LINK_SPEED_82598_AUTONEG (IXGBE_LINK_SPEED_1GB_FULL | \
+ IXGBE_LINK_SPEED_10GB_FULL)
enum ixgbe_eeprom_type {
ixgbe_eeprom_uninitialized = 0,
@@ -1248,6 +1257,7 @@ struct ixgbe_mac_operations {
enum ixgbe_media_type (*get_media_type)(struct ixgbe_hw *);
s32 (*setup_link)(struct ixgbe_hw *);
s32 (*check_link)(struct ixgbe_hw *, u32 *, bool *);
+ s32 (*get_firmware_version)(struct ixgbe_hw *, u16 *);
s32 (*setup_link_speed)(struct ixgbe_hw *, u32, bool, bool);
s32 (*get_link_settings)(struct ixgbe_hw *, u32 *, bool *);
};
@@ -1270,6 +1280,7 @@ struct ixgbe_mac_info {
u32 link_attach_type;
u32 link_mode_select;
bool link_settings_loaded;
+ bool autoneg;
};
struct ixgbe_eeprom_info {
distrib
>
Scientific%20Linux
>
5x
>
x86_64
>
by-pkgid
>
27922b4260f65d317aabda37e42bbbff
>
files
>
2818
